MBM BC-10 Instruction Manual

Provided By http://www.MyBinding.com http://www.MyBindingBlog.com MBM BC12 Multi Card CutterInstruction Manual

7 1. Installation Precautions  Recommended operating temperature range: 10–40°C  It is preferable to use the machine at a humidity of 50% or hi

8  Earth (ground) Earth terminal  No wet hands  Danger of an electric shock  Do not spill cold or hot water on the machine.  Do not place any

9 2. Part Names Top panel Front cover Rear cover Product receiver Operation panel Paper feed tray Slitter cover Trash box Power

10 Slitter unit Pressure roller unit Paper feed unit Slitter unit adjustment dial Slitter unit fixing thumbscrew Paper feed unit fixing th

11 3. Composition and Imposition  Composition: To design a form for the end product by combining characters, illustrations, images, etc.  Imposit

12 3.3 Method of composition and imposition The composition should be prepared based on your own design. Imposition should be made based on the po

13 Cutting Mode/Slitter Combination Table ご 確 認 願 います

14 BC-12 Prescribed Imposition Format Table (1/3) Cutting Mode 1 (Lettet) Cutting Mode 3 (Lettet) Cutting Mode 2 (Lettet)

15 VersaTrim Prescribed Imposition Format Table (2/3) Cutting Mode 4 (Lettet) Cutting Mode 7 (Lettet) Cutting Mode 5 (Lettet) Cutting

16 VersaTrim Prescribed Imposition Format Table (3/3) Cutting Mode 10 (Legal)

MULTI CARD CUTTER Operation Manual ＊Be sure to read this manual to operate the machine safty and proper

17 4. Preparations for Operation 4.1 Use this machine under the operating environment specified in “1. Installation Precautions”. 4.2 Attach the ne

18 4.3 If the outlet is not triplex (three-pins) (with ground wire), be sure to attach the provided adapter to the power plug and ground it. 4

19 5. How to Use 5.1 Operation panel Operation panel • Display panel The setting of the number of products to be cut, number of cut cards, etc.

20 5.2 Checking no error is displayed on the display panel  If the machine is in the normal condition, the Ready/Clear LED lamp lights up and the d

21 5.5 Selecting the cutting mark function  Each time the Cutting Mark Key is pressed, the red pilot LED lamp light up or goes off.  If you do

22 5.6 Selecting the counter mode  If the adding mode is selected using the Mode Key, the adding LED lamp lights up and the cumulative number of cu

23 5.8 Starting operation  Press the Start Key to start operation.  The Start LED lamp (green) is lit while the machine is in operation, and the

24 5.11 Adjusting the right and left side margins (direction of the short side of letter-size paper)  The right and left side margins (direction of

25 Slitter unit fixing thumbscrew Slitter cover Slitter unit Handle portion Slitter unit fit

26 5.13 Removing a paper jam  To make it easier to remove a sheet or scrap of paper jammed inside the machine, each unit can be removed or op

Operation Manual V.1.0 October 2009 BC-12 MULTI CARD CUTTER

27 5.13.1 When “E002” is displayed  “E002” indicates the cutter unit may have stopped during cutting operation.  Turn off the power switch, open

28 Paper feed unit Top panel S2 sensor First delivery roller The cutter unit is behind here. Never put your fi

29 5.13.2 When “E006” is displayed  “E006” indicates that a sheet of paper was drawn into the machine but it was stopped because the sensor that

30  Install the pressure roller in the proper position, close the top panel and slitter cover, and turn on the power.  If “E007” is still displayed

31 6. Handling the Trash Box  While cutting is in progress, cut strips are collected in the trash box.  When the box becomes too full with margi

32 8. Maintenance 8.1 Maintenance check and replacing the pick-up roller  If the pick-up roller in the paper feed unit becomes worn out and

33 8.3 Replacing the blade  When cut edges are no longer crisp, it is time to replace the blade.  If the short side of letter-size paper (vertic

34 9．Option 9.1 Slitter Unit ＊The machine comes with BC and FD slitter unit at the time of purchase. (Either B90 or B85 can be selected at t

35 10. Troubleshooting Q&A If you think the machine is out of order, check the following first. Q1 The display panel and all pilot LED lamps

36 Q6 The blade does not cut partly.  There may be nicks in the blade. If so, it is necessary to replace or repair the cutter unit or slitter unit.

1 BC-12 Operation Manual Contents Introduction ···································································································

2 Explanation of Symbols The following safety symbols are used in this operation manual and on the labels attached to the machine body.

3 Safety Instructions Connect the power plug into an outlet rated at 120V. It is prohibite

4 Before removing jammed paper, first turn off the power switch. To remove a sheet of paper caught in

5 Remove the power plug from the outlet when the machine will not be used for a long time. When moving the machine, first

6 Main Specifications Supported paper size letter-size 11”×8.5” (279.4215.9mm, within ±0.5mm from each side) Paper thickness